SnowBear by Marlon AVAL8219 82 in. x 19 in. Universal Snow Plow with Wireless Winch

It is important to check all nuts and bolts and ensure they are tight before you plow. You can put dielectric grease (petroleum jelly) on the grey quick connection to avoid electrical issues.

You cannot fix your winch pin, the winch pin is now compromised. Please contact support@detailk2.com or visit https://detailk2.com/warranty and submit a warranty claim.

This is a very common mistake customers make during assembly. The middle section of the scraper blade is the longest piece and the two short ones go on the ends. If they aren’t lining up try flipping the scraper blade over.

The 35 AMP circuit breaker is necessary to prevent possible electrical damage to either the winch or the vehicle’s electrical system. You connect it to the red wire going from the control box to the battery.

Ensure you have read and understand your provided DK2 snowplow manual and follow all instruction before use, this will prevent any potential damage to your vehicle or snowplow. Our snowplows are designed to minimize the wear and tear on your vehicle. We recommend you remove your snowplow when it is not in use.

The T-frame (Universal) style snow plows (Hitch-Mounted Series) mount on to any vehicle with a standard 2” class III front mount receiver. The custom mount snow plows (Summit II, Rampage II, Storm II) use a set of vehicle specific mounting brackets joined by a cross member which connects the plow frame to the frame of your vehicle.

To ensure compliance with road safety and regulation, a snowplow light kit is required in order to drive on any road. Please abide by local road laws and regulations as they can vary by location. We recommend you stay off of highways and stick to streets instead. Before driving on any road, it is always important make sure the safety clips or the hitch pin are secured and your plow is safely mounted to your vehicle. You are required to use the safety chain while you aren’t plowing to take stress off your winch strap.

The operator of the plow can decide how high to set the skid shoes. We recommend setting them about 1/4 of an inch below the scraper blade. The skid shoes will help protect the surface you are plowing and also prevent wear on your scraper blade.

If you hear a clicking there is a good chance your winch relay (black control box) isn’t working. You can check that your winch is fine by hooking up a power source directly to the winch and by pass the control box. If the winch works fine you need a new WCB (winch control box).

This is a sign that you have a defective WCB (winch control box). Please reach out to support@detailk2.com or submit a warranty claim at https://detailk2.com/warranty

If the light on your wireless remote is flashing red, make sure that:

1. You've confirmed that the issue is in fact with your wireless remote by first plugging in your wired remote and try using the controls.
2. The ground wiring coming from your transmitter box is going back to the negative terminal on your battery.
3. You have tried changing the battery on your remote.
4. You have tried resetting your wireless remote.

Resetting your wireless remote:

1. Take off one of the leads from your battery (positive or negative)
2. Turn on the remote's wireless emitter and press the IN and OUT button simultaneously for 3 seconds. After 3 seconds, the wireless remote light will turn a solid green.
3. Reconnect the lead back to your battery.

If you have attempted all techniques and are still not getting a functional remote, you may need to replace your wireless remote.

Is your remote within the warranty period?

Please visit https://detailk2.com/warranty to fill out our warranty form so we can send you a replacement covered by your included 1-year limited warranty.

Is your remote outside its warranty period?

Please visit the DK2 parts store at https://detailk2.com/parts/snowplow-parts (US Customers) or https://detailk2.ca/parts/snowplow-parts (Canadian Customers) to purchase a brand new wireless remote kit for your DK2 Snowplow.

You are able to convert your Hitch-Mounted Snowplow by purchasing the following items:

A CRM3312 Cross-Member

And the corresponding Custom Mount Kit that fits to your specific vehicle Make/Model/Year (please see the Custom Mount Guide by clicking here, you can shop for Custom Mount Kits by clicking here)